U225X / ENGINEERING UNWARRANTED

ASA Hose Adapter / Finding Where the Print Time Went

Public record / 3DP-ASA-HOSE-001 / Revision A

PUBLIC RECORD
U225X

I wanted a practical ASA profile for a hose adapter on the Creator 5 Pro, using a 0.4 mm nozzle in Flash Studio Desktop. The conservative starting settings made the estimate much longer than expected. The useful part of this experiment became finding which operations consumed the time, changing those settings, and checking the next slice. The documented result stops at a 6 h 19 min estimate. The later 0.16 mm proposal still needs a slice and a physical test; no completed adapter or pressure capability is claimed here.

STATUSSLICER TRIAL / PRINT TEST PENDINGCLASSIFICATION3DPMATERIALOVERTURE ASA / CREATOR 5 PRODATE2026.10.10

TECHNICAL NOTES

A functional garden-hose adapter turned a three-hour estimate into nine hours. Reading the slicer's time breakdown led to a six-hour estimate and a proposed change from 0.12 to 0.16 mm layers.

BUILD STORY

This is a record of slicer tuning before a print. The settings discussed were experiments for this model and material, not a validated ASA profile or a certified hose fitting.

The starting request fixed two variables: a 0.4 mm nozzle and 0.12 mm layers. I identified the printer as a Creator 5 Pro and the slicer as Flash Studio Desktop. Once the material and use were clarified as Overture ASA and a garden hose, the proposed starting profile favored a dense part with six walls and 100% infill. Those were trial settings, not evidence that the adapter could hold pressure.

The time estimate immediately changed the conversation. I reported that a roughly three-hour print had become a nine-hour print. The reviewed breakdown put about 5 h 14 min into inner walls and 2 h 16 min into outer walls, with less than ten minutes in supports. That made wall paths the first place to investigate. Removing the one supported area would not address most of the delay.

The next proposal increased the wall and infill speeds and reduced the small-perimeter threshold from 10 to 5 mm while keeping 0.12 mm layers, six walls, and 100% infill for comparison. OrcaSlicer's documentation explains why the threshold matters: short perimeter paths can use a separate, slower speed. It also notes that actual speeds remain constrained by volumetric flow, motion limits, and acceleration. The revised values were a tuning trial, not a promise that the printer would reach every requested speed.

The next report was concrete progress in the slicer: the estimate had fallen to about six hours, with the reviewed total at 6 h 19 min. Walls still occupied about 4 h 09 min, and travel was nearly 54 minutes. This was a better estimate, not a finished six-hour print. The record has no measured runtime, extrusion result, or comparison of the printed threads.

I then clarified that the part was functional and that cosmetic finish was not a priority, so 0.16 mm layers became an acceptable next experiment. For the same height, that means approximately 25% fewer layers than 0.12 mm, but it does not guarantee a 25% shorter job. The discussion also proposed checking the Avoid crossing walls setting, which can add travel detours according to OrcaSlicer's documentation. A four-hour result was only a target; no follow-up slice established it.

The next useful record is a saved 0.16 mm slice with its full time breakdown, followed by a small representative print to check the threads, shoulder, support removal, and layer bonding. The adapter geometry and final slicer project still need to be attached. A hose connection also needs its sealing and water-use results documented separately. Nothing in the estimates establishes a pressure rating, and the current project remains an unvalidated prototype.

SPECIFICATION

PrinterFlashforge Creator 5 Pro, as identified in the project discussion

SlicerFlash Studio Desktop

Material and nozzleOverture ASA / 0.4 mm nozzle

Intended partAdapter for a garden hose carrying pressurized water

Initial layer height0.12 mm

First reported changeAbout 3 hours before the conservative profile; about 9 hours afterward

Wall-time diagnosisInitial breakdown: approximately 5 h 14 min inner walls + 2 h 16 min outer walls

Revised estimate6 h 19 min after the first speed changes; estimated time, not elapsed print time

Next proposed trial0.16 mm layers; no resulting slice recovered

Physical validationNo finished print, fit check, leak result, or pressure rating recorded

NEXT TO ADD

The adapter CAD/STL and its source or license information
Saved slicer project or profile with the final settings and software version
The 0.16 mm slice screenshot and full time breakdown
A finished-print photo, actual elapsed print time, and notes on layer bonding and support removal
Measured thread/washer fit and documented water-use test conditions and results; pressure capability remains unverified

DEVELOPMENT HISTORY

2026.10.10STARTRequested a 0.12 mm ASA profile for a Creator 5 Pro with a 0.4 mm nozzle; clarified Overture filament and garden-hose water service.

2026.10.10SLICEReported that the conservative profile increased the estimate from roughly three hours to nine hours. The review identified walls as the main time consumer.

2026.10.10REVISIONReported an estimate down to about six hours after speed changes; the reviewed estimate was 6 h 19 min.

2026.10.10NEXT TRIALAccepted considering 0.16 mm layers because function mattered more than cosmetic finish. The conversation ended before a new slice or print result.

2026.10.10APublished the tuning chronology with estimates separated from physical results and the outstanding checks listed explicitly.